JavaScript seems to be disabled in your browser.
You must have JavaScript enabled in your browser for full functionality of this website.

Concrete Anchors & Fasteners is Our Specialty   Questions? Contact Mike   

You have no items in your shopping cart.
Free Shipping
For orders $25
or more within
the USA

3/4" x 5-1/2" Red Head Trubolt 304 Stainless Steel Wedge Anchor, 10/Box

   Availability: In Stock
  Questions? Email Mike

$179.01 per Box of 10
    Payment types
Purchase ITW Red Head Trubolt 3/4" x 5-1/2" Red Head Trubolt 304 Stainless Steel Wedge Anchor directly online; shipping is free and fast.
SKU: WW3454


Customer Reviews

ITW/RedHead® - 3/4" x 5-1/2" Red Head Trubolt (three zero four) 304 Stainless Steel Wedge Anchor

The 3/4" x 5-1/2" Red Head Trubolt (three zero four) 304 Stainless Steel Wedge Anchor (10 pcs per box) are designed for attaching to concrete. Every order will be shipped directly from the Cleveland, Ohio warehouse for delivery in 1 to 3 days.

  • Bit size 3/4"
  • Minimum embedment 3-1/4"
  • Thread Length 3-5/8"
  • 304 stainless steel for use in wet environments
  • Not acceptable for use in a vibratory load
  • Packaged with 304 stainless steel nuts and washers
  • 3/4" inch diameter x 5-1/2" inch length
  • Must space anchor a minimum of 5" from each other
  • Every order over $25.00 ships for free
Products specifications
Bit Size 3/4"
Minimum Embedment 3-1/4"
Thread Type 3/4" - 10
Type Male
Primary Concrete only
Diameter 3/4"
Length 5-1/2"
Material 304 Stainless Steel
Environment Wet
Box Qty 10
Maximum Fixture Thickness 2-1/4"
Minimum Fixture Hole Diameter (Hole Spotted) 3/4"
Length ID Code I
Wrench Size For Nut 1-1/8"
Length Measurement End to End
Country American Made
Brand Name ITW/RedHead

The 3/4" x 5-1/2" Red Head Trubolt (three zero four) 304 Stainless Steel Wedge Anchor is made from (three zero four) 304 Stainless Steel. This anchor is designed for use in concrete only, and should never be used in block or brick base material.

The anchor is designed for use in a wet environment.

Hole Diameter/Bit Diameter
The anchor requires a 3/4" hole to be drilled in the base material (concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the 3/4" x 5-1/2" Red Head Trubolt (three zero four) 304 Stainless Steel Wedge Anchor is 3/4".

Length Anchor
The length of the anchor is 5-1/2", and is measured as an overall length of the anchor from end to end.

Thread Type
The threads on the anchor are national coarse threads that measures 3/4" with 10 threads per inch, commonly referred to as 3/4"-10.

Thread Length
The length of the threads on the anchor is 3-5/8" in length.

The anchor is packaged with 10 pieces per box and is packaged with the correct number and diameter of nuts and washers.

Minimum Embedment
The anchor minimum embedment into the concrete is 3-1/4". Therefore, the anchor must be installed so that a minimum of 3-1/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-1/4". This will ensure that the minimum embedment of 3-1/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/4" diameter anchor requires the hole in the fixture to be 13/16".

Wrench Size
The size of the wrench required to turn the nut to set the anchor is 1-1/8".

Torque Value
The maximum torque that can be applied to the anchor once installed is 110 Ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 11-3/8" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 5-11/16" from an unsupported edge of the concrete.

The anchor is stamped with the letter I on the threaded end to allow inspection of the anchor after installation. The letter "I" designates an overall length of the anchor as between 5-1/2" up to, but not including 6" in length.

Holding Values - Ultimate Load Values in 2000 PSI Concrete

anchor Size

Minimum Embedment

Pull-Out (lbs.)

Shear (lbs.)

3/4" x 5-1/2"




Product Information


Part number

Quantity per Box

3/4" x 5-1/2" Red Head Trubolt (three zero four) 304 Stainless Steel Wedge Anchor



Installing a 3/4" x 5-1/2" Red Head Trubolt (three zero four) 304 Stainless Steel Wedge Anchor
  1. Select a carbide drill bit with a diameter equal to the anchor diameter. Drill a hole at least 1/4” deeper than nominal anchor embedment.
  2. Clean hole with pressurized air or vacuum to remove any excess dust/debris.
  3. Using the washer and nut provided, assemble the anchor, leaving nut one half turn from the end of the anchor to protect threads. Drive anchor through fixture to be fastened until washer is flush to surface of fixture.
  4. Expand anchor by tightening nut to the specified setting torque – see torque table (approx3 to 5 full revolutions).
  5. Warning! Use in concrete ONLY. Not recommended for use in lightweight masonry such as block or brick.
  6. Warning! Always wear safety glasses and other necessary protective devices or apparel when installing or working with anchors.
  7. Caution: Use of core drills is not recommended to drill holes for use with this anchor.
  8. Do not use an impact wrench to set or tighten the anchor. Not recommended for use in concrete which has not had sufficient time to cure.
  9. The use of carbide drill bits manufactured with ANSI B212.15 drill bit diameter requirements is recommended for installation of this anchor. Anchor spacing and edge distance (anchor installation locations) are the responsibility of the engineer of record.
  10. Installing product in oversized hole is not recommended. Product will not set properly or achieve full designed load in oversized hole.

3/4" x 5-1/2" 304 stainless steel wedge anchor - concrete - steel guards


* The figures above indicate average ultimate tension and shear failure values. A safety factor of 4:1 or 25% of ultimate value is generally accepted as a safe working load. Reference should always be made to applicable codes.

These bits work with the selected anchor
Back to product