Concrete Anchors & Fasteners is Our Specialty   Questions? Contact Mike   

You have no items in your shopping cart.
Free Shipping
For orders $25
or more within
the USA

1/4" x 2" Round Slotted Sleeve Anchor Zinc Plated, 100/Box

Not available
Presently Out of Stock

Need to purchase the 1/4" x 2" Round Slotted Sleeve Anchor Zinc Plated? Buy direct to save. All orders ship immediately with no charge for freight. SAR142

CONFAST® - 1/4" x 2" Round Slotted Sleeve Anchor Zinc Plated

The 1/4" x 2" Round Slotted Sleeve Anchor Zinc Plated are packaged 100 pieces per box, and are used for indoor, dry applications. The head is round slotted, and is expanded using a standard straight screwdriver. Orders will ship on same day received, and will be delivered to most locations in the United States in 1 to 3 business days.

  • Bit size 1/4"
  • Minimum embedment 1"
  • Head is round slotted
  • Anchor expanded using standard screwdriver
  • Assembled for fast, easy installation
  • Anchor does not require bottom of hole for expansion
  • Three parts: body, sleeve, round post nut
  • 1/4" diameter x 2" (two inches) length (length measured from under the head)
  • $25.00 order qualifies for free freight anywhere in the continental U.S.
Products specifications
Bit Size 1/4"
Minimum Embedment 1"
Thread Type 3/16" - 24
2000 PSI Concrete - Pull-Out (lbs.) * 682
2000 PSI Concrete - Shear (lbs.) * 840
Type Male
Diameter 1/4"
Length 2"
Material Carbon Steel Zinc Plated
Environment Dry
Box Qty 100
Minimum Spacing 2-1/2"
Minimum Edge Distance 1-1/4"
Maximum Fixture Thickness 1"
Minimum Fixture Hole Diameter (In Place) 5/16"
Length Measurement Underneath head
Brand Name CONFAST

The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete, Block, and Brick.

The anchor is designed for use in a Dry environment.

Head Style
The anchor is a Round head and is designed to allow the head to sit on top of the surface of the item being attached.

Hole Diameter/Bit Diameter
The anchor requires a 1/4" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 1/4".

Length Anchor
The length of the anchor is 2"

Thread Type
The threads on the anchor are national coarse threads that measures 1/4" with 24 threads per inch, commonly referred to as 1/4"-24 .

The anchor is packaged with 100 pieces per box and comes assembled with round slotted post nut.

Minimum Embedment
The minimum anchor embedment into the concrete is 1". Therefore, the anchor must be installed so that a minimum of 1" of the anchor is embedded into the concrete.

Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1". This will ensure that the minimum embedment of 1" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4" diameter anchor requires the hole in the fixture to be 5/16".

Wrench Size
The size of the wrench required to turn the nut to set the anchor is flat screw driver.

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 2 - 6 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 2-1/2" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 1-1/4" from an unsupported edge of the concrete.

Holding Values - Ultimate Load Values in 2000 PSI Concrete

Anchor Size

Minimum Embedment

Pull-Out (lbs.)

Shear (lbs.)

1/4" x 2"




Installing a 1/4" x 2" (two inches) Round Slotted Sleeve Anchor Zinc Plated
  1. Drill a 1/4" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
  2. Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 1" is met.
  3. The hole can be drilled while the fixture is in place. The minimum hole in the fixture for the 1/4" x 2" (two inches) Round Slotted Sleeve Anchor Zinc Plated is 5/16".
  4. Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
  5. The 1/4" x 2" (two inches) Round Slotted Sleeve Anchor Zinc Plated is manufactured and sold fully assembled with nut and washer. It is important that the nut is on the end of the threads to protect the threads when it is struck by a hammer during installation.
  6. Insert the anchor though the fixture hole and into the hole in the base material. A hammer will be required to pound the sleeve anchor into the base material until the washer and nut are tight against the fixture.
  7. Tighten the nut on the 1/4" x 2" (two inches) Round Slotted Sleeve Anchor Zinc Plated until finger tight by turning clockwise.
  8. Using a flat screwdriver, turn the nut 2 to 4 times until snug or until the proper torque value of 2 - 6 Ft./lbs. is reached.
  9. Always use proper personal protective equipment per manufacturer's and OSHA instructions.

1/4" x 2" round head stainless steel sleeve anchor - brick - light fixture 1/4" x 2" round head stainless steel sleeve anchor - block - junction box 1/4" x 2" round head stainless steel sleeve anchor - block - outside light fixture


Product/Company Reviews

* The figures above indicate average ultimate tension and shear failure values. A safety factor of 4:1 or 25% of ultimate value is generally accepted as a safe working load. Reference should always be made to applicable codes.

* The bits are recommended by diameter and may not necessarily be the length needed for your application. Please make sure the usable length will work for your application. *

These bits work with the selected anchor
Back to product