1/4" x 2" Split Drive Flat Zinc Plated (100 pieces per box) are used for fastening wood to solid concrete. In stock and all orders will be received in 1 to 3 business days when shipped in the continental United States.
Bit size 1/4"
Minimum embedment 1-1/8"
Tamper resistant head
Indoor use only - zinc plated
Pre-expanded friction type anchor
Not for use in vibratory loads
1/4" in. is the diameter x 2" (two inches) in. is the length
Spacing - a minimum 2-1/2"
All order shipped in continental U.S. over $25.00 ship freight free
Products specifications
Bit Size
1/4"
Minimum Embedment
1-1/8"
2000 PSI Concrete - Pull-Out (lbs.) *
990
2000 PSI Concrete - Shear (lbs.) *
1248
Type
Male
Primary
Concrete only
Diameter
1/4"
Length
2"
Material
Carbon Steel Zinc Plated
Environment
Dry
Box Qty
100
Minimum Spacing
2-1/2"
Minimum Edge Distance
1-1/4"
Maximum Fixture Thickness
7/8"
Minimum Fixture Hole Diameter (In Place)
3/8"
Head Type
Flat Countersunk
Brand Name
CONFAST
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load
Applications The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.
Environment The anchor is designed for use in a Dry environment.
Head Style The anchor is a Flat Countersunk head and is designed to prevent the head from protruding above the surface of the item being attached.
Hole Diameter/Bit Diameter The anchor requires a 1/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
Diameter of Anchor The diameter of the anchor is 1/4".
Length Anchor The length of the anchor is 2"
Packaging The anchor is packaged with 100 pieces per box .
Minimum Embedment The minimum anchor embedment into the concrete is 1-1/8". Therefore, the anchor must be installed so that a minimum of 1-1/8" of the anchor is embedded into the concrete.
Depth of Hole The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.
Maximum Fixture Thickness The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 7/8". This will ensure that the minimum embedment of 1-1/8" will be met.
Fixture Hole Diameter The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4" diameter anchor requires the hole in the fixture to be 3/8".
Spacing between Anchors Each anchor must be spaced a minimum distance of 2-1/2" from each other when measured center to center.
Edge Distance It is very important not to install the anchor any closer than 1-1/4" from an unsupported edge of the concrete.
Holding Values - Ultimate Load Values in 2000 PSI Concrete
Anchor Size
Minimum Embedment
Pull-Out (lbs.)
Shear (lbs.)
1/4" x 2"
1-1/8"
990
1248
Installing a 1/4" x 2" (two inches) Split Drive Flat Zinc Plated
Drill a 1/4" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 1-1/8" is met.
The hole can be drilled while the fixture is in place. The minimum hole in the fixture for the 1/4" x 2" (two inches) Split Drive Flat Zinc Plated is 3/8".
Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
Insert the 1/4" x 2" (two inches) Split Drive Flat Zinc Plated through the material to be fastened and into the hole, ensuring that the bottom of the head is sitting flush with the fixture plate.
Hammer the anchor until the head of the anchor is tight against the item being fastened.
Always use proper personal protective equipment per manufacturer's and OSHA instructions.
