CONFAST® - 1/4" x 5" Hex Head CONFAST® Concrete Screw
The CONFAST® 1/4" x 5" (five inches) Hex Head Blue masonry screws are packaged 100 pieces per box with one bit included free of charge. They work well in solid concrete, brick or block, and are designed for indoor atmospheres that are dry. Every order ships from the Cleveland, Ohio warehouse for delivery in the United States within 1 to 3 business days.
Bit size 3/16"
Minimum embedment 1"
5/16" nut driver nut setter is used for driving the CONFAST® screw
Do not exceed 1-3/4" embedment
Placement is closer to the edge than expansion type anchors
Can be inserted through hole in item being attached
Taps threads in masonry
1/4" inch diameter x 5" (five inches)inch length (measured from under head)
All orders over $25.00 ship for free
Products specifications
Bit Size
3/16"
Minimum Embedment
1"
Thread Length
1-1/4"
Thread Type
High-Low
2000 PSI Concrete - Pull-Out (lbs.) *
562
2000 PSI Concrete - Shear (lbs.) *
675
Type
Male
Diameter
1/4"
Length
5"
Material
Carbon Steel - Blue Coated
Environment
Dry
Box Qty
100
Minimum Spacing
4"
Minimum Edge Distance
3"
Maximum Fixture Thickness
3-1/2" to 4"
Minimum Fixture Hole Diameter (In Place)
5/16"
Minimum Fixture Hole Diameter (Hole Spotted)
5/16"
Head Type
Hex Washer
Length Measurement
Underneath head
Driver Size
5/16"
Brand Name
CONFAST
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load
Applications The anchor is made from Carbon Steel, and is Blue. This anchor is designed for use in Concrete, Block, and Brick.
Environment The anchor is designed for use in a Dry environment.
Head Style The anchor is a Hex Washer head and is designed to allow the head to sit on top of the surface of the item being attached.
Hole Diameter/Bit Diameter The anchor requires a 3/16" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
Driver Required A 5/16" is required for driving the anchor into the base material.
Diameter of Anchor The diameter of the anchor is 1/4".
Length Anchor The length of the anchor is 5"
Thread Length The length of the threads on the anchor is 1-1/4" in length.
Packaging The anchor is packaged with 100 pieces per box and one (1) correct sized carbide bit.
Minimum Embedment The minimum anchor embedment into the concrete is 1". Therefore, the anchor must be installed so that a minimum of 1" of the anchor is embedded into the concrete.
Depth of Hole The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.
Maximum Fixture Thickness The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 3-1/2" to 4". This will ensure that the minimum embedment of 1" will be met.
Fixture Hole Diameter The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4" diameter anchor requires the hole in the fixture to be 5/16".
Spacing between Anchors Each anchor must be spaced a minimum distance of 4" from each other when measured center to center.
Edge Distance It is very important not to install the anchor any closer than 3" from an unsupported edge of the concrete.
Bolt Length When a bolt is used in conjunction with the anchor, the length of the bolt needed is determined by considering these factors:
Flush With Concrete - when the anchor is set flush with the surface of the concrete, add the thickness of the material being fastened to the thread length of 1-1/4", and then add the space for any washers used.
Below Surface of Concrete - add the depth below the surface of the concrete to the thickness of the material being fastened, then add the space for the washer, and, finally, add 1-1/4" for the thread engagement.
Holding Values - Ultimate Load Values in 2000 PSI Concrete
Anchor Size
Minimum Embedment
Pull-Out (lbs.)
Shear (lbs.)
1/4" x 5"
1"
562
675
Installing a 1/4" x 5" (five inches) Hex Head CONFAST® Concrete Screw
Drill a 3/16" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 1" is met.
The hole can be drilled while the fixture is in place. The minimum hole in the fixture for the 1/4" x 5" (five inches) Hex Head CONFAST® Concrete Screw is 5/16".
Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
Insert the point of the 1/4" x 5" (five inches) Hex Head CONFAST® Concrete Screw into the hole. Make sure that the screw being installed will penetrate the base material a minimum of 1" but no deeper than 1-3/4".
Using a 5/16" nut driver hex driver for the anchor , turn the screw clockwise, applying slight pressure until the head of the screw is snug against the material being fastened.
Always use proper personal protective equipment per manufacturer's and OSHA instructions.