CONFAST® - 3/8" Machine Screw Anchor
The 3/8" Machine Screw Anchor is preassembled and packaged with 50 pieces per box. This anchor requires the use of a setting tool to set the anchor in the masonry material. They are fully stocked in the Cleveland, Ohio warehouse so that all orders ship the same day. All orders $25.00 or more will ship for free.
- Bit size 3/4"
- Minimum embedment 1-1/4"
- Designated diameter is equal to bolt diameter
- Anchor has national coarse threads
- Very versatile, can be used in most masonry materials
- Highly corrosion resistant
- Do not use in vibratory loads
- Insert with threaded open end up
- Not recommended for overhead applications
- Proper setting tool must be used
- Freight is free for orders $25.00 and more
|Thread Type||3/8" - 16|
|2000 PSI Concrete - Pull-Out (lbs.) *||1488|
|Material||Anchor Body Antimonial Lead Alloy/Cone Zamac Alloy|
|Minimum Edge Distance||3-3/4"|
|Minimum Fixture Hole Diameter (In Place)||7/8"|
|Minimum Fixture Hole Diameter (Hole Spotted)||3/8"|
|Inside Anchor Diameter-Bolt Diameter||3/8"|
|Outside Anchor Diameter||3/4"|
|Internal Thread Length||1"|
|Length Measurement||End to End|
|Bolt Length||Fixture Thickness + Embedment Depth|
The anchor is made from Anchor Body Antimonial Lead Alloy/Cone Zamac Alloy. This anchor is designed for use in Concrete, Block, and Brick.
The anchor is designed for use in a Moist environment.
Hole Diameter/Bit Diameter
The anchor requires a 3/4" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
The designated size of the anchor refers to the inside diameter 3/8" of the anchor or the diameter of the threaded rod or bolt that can be inserted into it.
Diameter of Anchor
The diameter of the anchor is 3/8".
The length of the anchor is 1-1/4"
The threads on the anchor are national coarse threads that measures 3/8" with 16 threads per inch, commonly referred to as 3/8"-16 .
Each anchor must be set in the concrete with a specific setting tool. The anchor is set using the 3/8" setting tool which is sold separately.
The anchor is packaged with 40 pieces per box and does not come with a setting tool.
The minimum anchor embedment into the concrete is 1-1/4". Therefore, the anchor must be installed so that a minimum of 1-1/4" of the anchor is embedded into the concrete.
Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.
Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/8" diameter anchor requires the hole in the fixture to be 7/8".
The maximum torque that can be applied to the anchor once installed is 10 ft./lbs.
Spacing between Anchors
Each anchor must be spaced a minimum distance of 7-1/2" from each other when measured center to center.
It is very important not to install the anchor any closer than 3-3/4" from an unsupported edge of the concrete.
Holding Values - Ultimate Load Values in 2000 PSI Concrete
3/8" x 1-1/4"
- Drill a 3/4" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
- The depth of the hole can be deeper or equal to the minimum embedment depth of 1-1/4" which is equal to the length of the anchor .
- Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
- Insert the anchor into the hole with the threaded cone end first.
- Take the correct 3/8" Machine Screw Anchor setting tool and insert the smaller diameter end into the open end of the 3/8" Machine Screw Anchor.
- Strike the end of the setting tool with a hammer until the anchor is fully set.
- The 3/8" Machine Screw Anchor is now set. A 3/8" diameter bolt can be inserted into the 3/8" Machine Screw Anchor with a maximum torque of 10 ft. lbs.
- Always use proper personal protective equipment per manufacturer's and OSHA instructions.